Hamamatsu

This page was created to understand some Vidicon repair and interchanagability

Catalog

C2400-16 1-inch Super- Harpicon. 400 to 700 nm, 0.001 to 10 lux

Vidicon

Heads:

Model	Connector	For	Tube	Resolution	Sensitivity	Yoke	Notes
C790-10		X-ray	No silkscreen Metal: 1206341 IDI USA			XVC-492E
C2400-03		IR 800-2100 nm 400-1800 nm	1"	720 x 576 600 line	0.1-10 lux		Lens: Xenoplan 1,4/23 mm Advertised in new catalog as the only modern IR vidicon supported
C2400-05		UV 250-750 nm	1"	700 line	0.01-1 lux
C2400-07		Visible microscope	Newvicon / Matsushita				Advertised in new catalog as the only modern general vidicon supported
C2400-08		400-850 nm?	1" ?			XVC-492E	McMaster Fiber bundle, fluoroscope, or something weird like that. Has electrical connection? Tube hard to get to, but could take out if really determined. Would need to remove either (fiber bundle connector?) or most of the electronics
C2400-53		IR 400-1800 nm	2/3"	550 line	0.1-10 lux
C2400-55		UV 250-750 nm	2/3"	700 line	0.01-1 lux
C2741-		400-850 nm	1" NEWVICON S4076 MATSUSHITA				McMaster weird poorly marked unit Much faster tube response than C2741-03 S/N 0131K
C2741-03		IR 400 to 1800 nm 400 to 2200 nm	N2606 N2606-06 1" Mc: N2606-10	600 horizontal EIA: 525x485 CCIR: 625x509	S/N: 46 dB p-p/rms	KV-5767	Datasheet McMaster has a few Dage LSC-70 replacement suggests could be PbS tube coating. Has some N2606 curves
C2741-03B		1800 nm	N2606-02				22/01/2008 £8,340 Package includes Camera Head, Controller Unit, Camera Cable & BNC to BNC Cable Also: PC2Vision Frame Grabber Card & Cable Set Wasabi for Video Acquisition & Analysis Software

C2400 and C2741 seem generally compatible. The one C2400 camera I have has a

"Vidicon camera fitted with an N2606-10 or N214 lead sulphide tube."

https://www.artisantg.com/info/PDF__48616D616D617473755F43323430305F43616D6572615F446174617368656574.pdf

Potential IR vidicon tubes:

• Matsushita 25PE14
• Mullard XQ1443
  • NEWVICON® television camera tube with a photoconductive target composed of cadmium and zinc tellurides featuring high resolution and an extremely high sensitivity extending into the near infrared region

Board	Label	Used on	Note
NSVP04-1	DEF FOCUS	C2400-08 C2741-03
113611B	PREAMP	C2741-03
113611A	PREAMP	C2400-08
0XVP02-2	DEF FOCUS	C790-10
0XVP01-2	PRE AMP	C790-10
0XPPOI-2	HV-POWER	C790-10

Tube

C790 X-Ray camera

moved from https://nucwiki.org/wiki/index.php/Hamamatsu_C790

mcmaster: got "X-RAY TV CAMERA" off of eBay missing cable. Both the camera and controller are marked C790-10 Was able to source something close to the needed CMC connectors and was able to retool for the proper cable. Now need to wire between them so I can boot the unit

Some relationship to Softex. Maybe they are used in Softex machines?

All wires on connector are used (at least on camera side).

Japan imports DDK JMSP2528 connector 025-028 silver-plated 28 core aviation plug 4 thick needle 24 thin needle

"Hamamatsu Softex X-Ray TV Camera controller C3205": seems to use the same connector

"Hamamatsu C6086 X-Ray Camera Controller": for CCD I think, not compatible

Head: MODEL C790, TYPE 10, SER.NO 88054284

Controller: MODEL C790, TYPE 10, SER.NO 88074380

Camera

Appears to be vidicon? Hard to see...in a black sub-enclosure. Enclosure is marked

YOKE ASSEMBLY XVC-492E HC-01 CHUOMUSEN CO., LTD. MADE IN JAPAN 378024

Boards:

• OXVPOI-2 PRE AMP
• OXPPOI-2 HV-POWER
• OXVPO2-2 DEF FOCUS

Maybe 22 or 24 AWG on connector. Power pins don't appear to use a larger gauge than the rest.

CCD

Model	Connector	For	Tube	Resolution	Yoke	Notes
C5840-10: EIA C5840-11: CCIR		IR 400 to 1650 nm	2/3"?			Datasheet Datasheet has graph comparing to C2741-03. TLDR: this is much less sensitive

C2741-63 camera controller

• 12PinCCD camera connector
• RS-232C
• 12PIN cable 5 m A3194-01
  

C6086 Series X-Ray CCD Camera

• 25 μm (C6086-03, 04)
• 30 μm (C6086-53, 54)
• 43 μm (C6086-13, 14)
• 62 μm (C6086-23, 24)
• Effective X-ray tube voltage range
• 10 to 100 kVp

https://www.artisantg.com/info/PDF__48616D616D617473755F43323430305F33325F33355F446174617368656574.pdf

https://www.artisantg.com/info/ATGckodl.pdf

C2400-77 2/3-inch Interline CCD

C2400-75 1/2-inch Interline CCD

McMaster

2019-12-09

Summary

-Composite capture working okay

-Pre-amp currently in iffy causes flicker

originally in "bad"

-Both C2741-03 tubes are slow response

-Each C2741-03 tube has a defect as currently used

Esj 54: poor SNR

Esj 31: uneven illumination

can be trimmed?

I believe they exhibit the same defect no matter the unit put into

-All 3 units use KV-5767 yoke assembly

-Pre-amps look like they are interchangable between C2741-03 and C2741-, but appear not to be

-Different tubes

C2741-03: N2606-10

C2741-: S4076

-Haven't touched C2400

-Haven't compard to

https://www.ebay.com/itm/4-Used-Tubes-3-Newvicon-S4076-Vidicon-Tube-One-RCA-8507A-Untested-But-Guaranteed/383310410334?hash=item593f14b25e:g:ByAAAOSwCL9d6HFD

4 Used Tubes-3 Newvicon S4076 Vidicon Tube One RCA 8507A Untested But Guaranteed

probably should get these to play with

2019-12-11

Swapped C790-10 tube into C2741 and it doesn't seem to produce any significantly better results. I was able to tune better, but significant defects still present. Took a video, maybe post

Several x-ray experiments on S4076. Its either not x-ray sensitive or very weakly sensitive. N2606 might be more sensitive though

TODO: review https://www.youtube.com/watch?v=FrXVpgP6IQw

2019-12-13

Comparing misc controllers:

• C790-10 X-RAY TV CAMERA, S/N 88074380
• C2741- CAMERA CONTROL UNIT, S/N 0131K
• C2741 CAMERA CONTROLLER, S/N 091264
• C2400 CAMERA CONTROLLER, S/N 931545

"CAMERA CONTROLLER"

• These appear basically identical in every regard I can tell except the C2741, which is literally a sticky label different
• Have different PCB revs, but this seems more of circumstance than an actual design difference
• Suggests C2741 was analog legacy design and C2400 is functionally equivalent digital design

Feature	C790 88074380	C2741 0131K	C2741 091264	C2400 931545
Construction		Analog Older Card cage Cable wraps Cage SHADING BOOS TER (ASC) INVERTER (ASC) SYNC	Digital Newer
Main board	Multi level Top: OXVP03-2 PROCESS	NSVP10-3 CAMERA CONTROL	113632B PROCESS	113632C PROCESS
Display		None	Digital OK	Digital Bad Swapping other 22CV10AP fixes
Camera connector		Top row fully populated	Missing pin on top row
Tuning		Screwdriver pots	Knobs
AGC connector		No	Labels almost implying there used to be a switch there
Transformer	Visually different C790-10J	C2400AT.J	C2400CT-UJ	C2400CT-UJ
Power PCB	CB0094B	CB0193	CB95Y27	CB95Y27