Difference between revisions of "ISI M-7"
(Created page with "Category:ISI {{:mcmaster:isi:m-7:m7front.jpg?300}}{{:mcmaster:isi:m-7:isicolumn.jpg?300}} Above: codename Smurf before I overhauled it. In the above unit it has a lot o...") |
|||
Line 1: | Line 1: | ||
[[Category:ISI]] | [[Category:ISI]] | ||
− | + | [[File:mcmaster_isi_m-7_m7front.jpg|300 px]][[File:mcmaster_isi_m-7_isicolumn.jpg|300 px]] | |
Above: codename Smurf before I overhauled it. In the above unit it has a lot of rust and other problems | Above: codename Smurf before I overhauled it. In the above unit it has a lot of rust and other problems | ||
Line 11: | Line 11: | ||
<code> | <code> | ||
Ultimate Vacuum: x10'''-6 mmHg | Ultimate Vacuum: x10'''-6 mmHg | ||
− | + | 10E-6 torr | |
Fore Pressure 3x10-1 mmHg | Fore Pressure 3x10-1 mmHg | ||
− | + | 100 mTorr | |
H. Power 100/0.35KW | H. Power 100/0.35KW | ||
− | + | 100VAC | |
− | + | 3.5 A | |
Pump Speed: 100 L/sec | Pump Speed: 100 L/sec | ||
Amount of Oil: 40cc | Amount of Oil: 40cc | ||
Line 26: | Line 26: | ||
Trying to figure out cooling. Options: | Trying to figure out cooling. Options: | ||
− | + | ** New Cole Parmer peristaltic pump w/ LS-15 tubing: 1L/min max | |
− | + | ** Warms up tubing at high speeds | |
− | + | ** DudaDiesel pump: min/max? | |
− | + | ** Too much? any chance I could break something? | |
− | + | ** Small pump | |
− | + | ** Test? | |
Chilling options | Chilling options | ||
− | + | ** FTC-350A from De Anza flea market | |
− | + | ** Early tests show that it might not necessarily work: outlet is not any colder than inlet | |
− | + | ** Large crycooler | |
− | + | ** Works | |
− | + | ** High current draw | |
− | + | ** -100C: potential to freeze water by accident |
Latest revision as of 11:36, 26 December 2018
Above: codename Smurf before I overhauled it. In the above unit it has a lot of rust and other problems
Diffusion pump
Dataplate
Ultimate Vacuum: x10-6 mmHg
10E-6 torr
Fore Pressure 3x10-1 mmHg
100 mTorr
H. Power 100/0.35KW
100VAC
3.5 A
Pump Speed: 100 L/sec
Amount of Oil: 40cc
No: 790123
TOKYO VACUUM MACHINERY Co. Ltd.
TOKYO JAPAN
Trying to figure out cooling. Options:
- New Cole Parmer peristaltic pump w/ LS-15 tubing: 1L/min max
- Warms up tubing at high speeds
- DudaDiesel pump: min/max?
- Too much? any chance I could break something?
- Small pump
- Test?
Chilling options
- FTC-350A from De Anza flea market
- Early tests show that it might not necessarily work: outlet is not any colder than inlet
- Large crycooler
- Works
- High current draw
- -100C: potential to freeze water by accident